Quiz summary
0 of 31 questions completed
questions:
Information
You have already completed the quiz before. Hence you can not start it again.
quiz is loading...
You must log in or register to start the quiz.
You must first complete the following:
Results
Results
0 of 31 questions answered correctly
Your time
Elapsed time
You have correctly answered 0 questions out of 0, giving you a result of 0.
Earned Point(s): 0 of 0,(0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not classified 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- Current
- Review
- Answered
- Exact
- Inexact
-
Question 1 of 31
1. Question
1. There are three large types of plans to represent structural drawings. What are they?
1- Mechanical plans
2- Cadastral plans
3- Architectural plans
4- Structural plans
5- General plans
6- Specific plans7- Development plans8- Evacuation plans
ExactInexact -
Question 2 of 31
2. Question
2. A sketch or a drawing is used to show:
ExactInexact -
Question 3 of 31
3. Question
3. The construction plan is the last one given to the client at the time of the closing of the project, true or false?
ExactInexact -
Question 4 of 31
4. Question
4. Find the intruder answer among the views given below.
ExactInexact -
Question 5 of 31
5. Question
5. Identify the information found in a layout plan.
1- Geodesic monuments
2- Number of lot
3- Orientation of lot in relation with the wind rose
4- Height of building
5- Number of windows
6- Interior finishes
7- Lateral margins
8- Surface lot
ExactInexact -
Question 6 of 31
6. Question
6. Identify the information found in an elevation drawing.
1- All of the building dimensions
2- The exterior finishes
3- The roof slope
4- The height of the building
5- The slope for water drainage
6- Dimension of openings
7- Benchmark values
8- The height of the foundation walls
ExactInexact -
Question 7 of 31
7. Question
7. A plan view is a bird's-eye-view, as if you were directly over the building. What is the first plan view found on all residential and commercial plans?
ExactInexact -
Question 8 of 31
8. Question
8. The doors and windows dimensions are always shown in the plan view. True or false?
ExactInexact -
Question 9 of 31
9. Question
9. If during an information research in an architectural plan, I know that I am on the right page, but I can't find the information, where could I find it?
1- I make up an answer from a previous project
2- I look for a balloon of a detailed in a detailed section near the location where should be the information
3- I look for a statement on the page where I am doing my research which is called "general information"
4- I read the "General information" page in the case of a commercial plan.
5- I ask the plumber
ExactInexact -
Question 10 of 31
10. Question
10. You are looking for information on the composition of an interior partition. Where will you find this information quickly?
ExactInexact -
Question 11 of 31
11. Question
11. When we talk about openings in blueprint reading, we are referring to doors and windows. In which order are these dimensions given for these openings? ex. 30''X36''
ExactInexact -
Question 12 of 31
12. Question
12. If you are asked to find an information related to interior finishes. Where will you find this information?
1- Elevation drawing
2- Detail view
3- Finishing legends
4- Mechanical plan
5- Information box
6- Finishing Chart7- Title page8- Plan viewExactInexact -
Question 13 of 31
13. Question
13. Where is the title box (reference box)?
ExactInexact -
Question 14 of 31
14. Question
14. The scale of the drawing is an important information from the reference box. It allows to shrink or enlarge an object while keeping the proportions. Give two types of scale rules?
1- Behavior rule2- Nominal rule3- Odd rule4- Metric rule5- Even rule6- Imperial rule7- Rule of thumbExactInexact -
Question 15 of 31
15. Question
15. The imperial system manages measurements in millimeters and meters.
True or false?ExactInexact -
Question 16 of 31
16. Question
16. What represent the broken lines in this schematic drawing?
ExactInexact -
Question 17 of 31
17. Question
17. In a detail bubble divided by three, what represent the number in the right lower corner?
ExactInexact -
Question 18 of 31
18. Question
18. What is a benchmark?
ExactInexact -
Question 19 of 31
19. Question
19. If you see an "f" at the bottom of a window on an elevation drawing, what does it mean?
ExactInexact -
Question 20 of 31
20. Question
20. If you see the inscription " type " near a dimension, a detail, or a roof slope, it means that all the dimensions, details or roof slopes are the same for the whole building. True or false?
ExactInexact -
Question 21 of 31
21. Question
21. What does this line represent on a technical drawing?
ExactInexact -
Question 22 of 31
22. Question
22. Identify the material that covers the interior of this wall section ..........
ExactInexact -
Question 23 of 31
23. Question
23. Where will you find the dimension that identifies the total height of the building in your plans?
ExactInexact -
Question 24 of 31
24. Question
24. If you need to work with a complicated commercial plan, which page will you use the most and use first when you will have to find information in your plan booklet?
ExactInexact -
Question 25 of 31
25. Question
25. What does RRH mean?
ExactInexact -
Question 26 of 31
26. Question
26. Where could I find the R value of the wool batt that will be installed in the ceiling under the roof?
ExactInexact -
Question 27 of 31
27. Question
27. Where can we find an information that cannot be drawn such as the density of the concrete footings?
ExactInexact -
Question 28 of 31
28. Question
28. Convert 235 square feet into square meters.
ExactInexact -
Question 29 of 31
29. Question
29. What would be the real measurement in meters of a 27 mm partition on a plane of 1 :100?
ExactInexact -
Question 30 of 31
30. Question
30. Find the volume of the required concrete to pour a slab for a basement of 17'-6''x 11'-3''x 0'-4''
ExactInexact -
Question 31 of 31
31. Question
31. Give an example of a mechanical plan.
ExactInexact